Adlink USB-1210

4-CH 16-Bit 2MS/s Simultaneous-Sampling USB DAQ Module
Caracteristici tehnice
Analog Input
Resolution 16-Bit
Number of channels 4 differential (simultaneous-sampling)
Maximum sampling rate 2MS/s per channel
Programmable gain 1, 5
Input range (Voltage) ± 10 V, ± 2 V
Offset error ± 1mV (gain=1)
± 0.2mV (gain=5)
Gain error Typical: ± 0.01% of FSR (gain=1 & 5)
Maximum: ± 0.02% of FSR (gain=1 & 5)
-3dB Bandwidth 600 kHz
CMRR (fin=1 kHz) 80 dB (gain=1)
90 dB (gain=5)
SFDR (fin=10 kHz) 98 dB (gain=1 & 5)
SINAD (fin=10 kHz) 89 dB (gain=1 & 5)
THD (fin=10 kHz) -100 dB (gain=1 & 5)
SNR (fin=10 kHz 89 dB (gain=1 & 5)
ENOB (fin=10 kHz) 14.3-bit (gain=1 & 5)
FIFO buffer size 256M Samples
Trigger sources Software, external digital, analog trigger ( from one analog input channel)
Trigger mode Post trigger, pre-trigger, delay trigger, middle trigger, gate trigger, post or delay trigger with re-trigger
External A/D conversion source Yes (from CONV)
Input coupling DC
Overvoltage protection Power on: ± 35 V
Power off: ± 15V
Input impedance 1 GΩ
Data transfer Programmed I/O, continuous (USB bulk transfer mode)
Function I/O
Mode* Digital I/O, general timer/counter, pulse generation
Digital I/O 8 DI / 4 DO (TTLLVTTL level)
General timer/counter Two 32-bit, base clock: 80 MHz, external to 10 MHz
Pulse generation Two PWM outputs (Modulation frequency: 0.01 Hz to 5 MHz; duty cycle: 1%-99%)
General Specifications
OS Information -Windows 7/8 x64/x86, Linux, and Mac
Software Compatibility -LabVIEW?
-MATLABR
-C/C++
-Visual Basic, Visual Studio.NET
Software Recommendations -U-Test
Interface USB 2.0 high speed
I/O connector Two 20-pin removable screw terminals
Operating temperature 0 to 55°C (32 to 131°F)
Storage temperature -20 to 70°C (-4 to 158˚F)
Relative humidity 5 to 95% non-condensing
Power requirements 5V@ 500 mA (USB bus powered)
Requirements 114 mm (H) x 156.5 mm (L) x 41.3 mm (W) (4.5” x 6.16” x 1.63”) (without connector and stand)
Documente
USB-1210_datasheet_en Datasheet

Managementul calităţii

Compania noastra are implementat sistemul de management al calitatii ISO 9001: 2015

Certificare ISO 9001:2015 - Sargon

Software industrial

Realizam software industrial de achizitie de date si control automat pe baza cerintelor clientului...

Detalii

Proiectare echipamente

Ati cautat echipamentul necesar dar nu ati gasit exact ce trebuia? Nicio problema, formulati-ne cerintele sistemului si noi vom...

Detalii

Atestat INSEMEX

Compania noastra este atestata GANEx - INSEMEX pentru proiectare, montaj, punere in functiune, mentenanta si inspectie instalatii tehnice care functioneaza in medii Ex

Vizualizare atestat